Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Modelo: HLG-150H
marca: Meanwell
Pacote: Caixa
produtividade: 20000pcs per month
transporte: Ocean,Land,Air
Lugar de origem: Guangdong, China
Apoio sobre: 5000pcs per month
porta: Shenzhen,Guangzhou,Hongkong
Tipo de pagamento: T/T,Paypal,Money Gram,Western Union
Incoterm: FOB,CIF
Fonte de alimentação impermeável do diodo emissor de luz de Meanwell HLG-150H
Descrição dos produtos
Fonte de alimentação impermeável do interruptor da saída 150W única , o seguinte modelo amplamente usado com Iseeled `s levou lâmpadas, GAN-150 H - 12, GAN-150 H -1 5, GAN-150 H -24, etc algum outro modelo para lâmpadas especiais com diferente tensão de entrada.
HLG-150 H -12 Blank: classificação IP67. Cabo para conexão de E / S.
HLG-150 H -12A: Classificação IP65. A tensão de saída e o nível de corrente constante podem ser ajustados através do potenciômetro interno.
HLG-150 H -12B: classificação IP67. Nível de corrente constante ajustável através do cabo de saída com sinal ou resistência de 1 ~ 10Vdc ou PWM.
HLG-150 H -12D (opção): classificação IP67. Função de escurecimento do temporizador, entre em contato com a MEAN WELL para obter detalhes.
Model |
HLG-150H-12 |
HLG-150H-15 |
HLG-150H-24 |
|
Output |
DC VOLTAGE |
12V |
15V |
24V |
CURRENT ADJ. RANGE |
Can be adjusted by internal potentiometer A type only |
|||
7.5-12.5A |
6-10A |
3.8-6.3A |
||
RATED POWER |
150W |
150W |
151.2W |
|
VOLTAGE ADJ. RANGE |
10.8-13.5V |
13.5-17V |
22-27V |
|
Input |
Voltage Range |
90-264VAC 127-370V DC |
||
Frequency Range |
47-63Hz |
|||
POWER FACTOR |
PF>0.98/115VAC, PF>0.95/230VAC, at full load (Please refer to "Power Factor Characteristic" curve) |
|||
Efficiency(Typ.)(230Vac) |
92% |
92.5% |
93.5% |
|
AC CURRENT (Typ.) |
1.7A / 115VAC 0.75A / 230VAC |
|||
INRUSH CURRENT(Typ.) |
COLD START 75A/230VAC |
|||
LEAKAGE CURRENT |
<0.75mA / 240VAC |
|||
PROTECTION |
OVER LOAD |
95~ 108% |
||
Protection type : Constant current limiting, recovers automatically after fault condition is removed |
||||
SHORT CIRCUIT |
Constant current limiting, recovers automatically after fault condition is removed |
|||
OVER VOLTAGE |
14-17V |
18-21V |
28-34V |
|
Protection type :Shut down O/P voltage, re-power on to recover |
||||
OVER TEMPERATURE |
100 ℃ up or less10 ℃ (RTH2) |
|||
Protection type : Shut down and latch off o/p voltage, recovers automatically after temperature goes down |
||||
Environment |
WORKING TEMP. |
-40 ~ +70 ℃(Refer to output load derating curve) |
||
WORKING HUMIDITY |
20 ~ 95% RH non-condensing |
|||
SAFETY |
SAFETY STANDARDS |
UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1, J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1 |
||
WITHSTAND VOLTAGE |
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC |
|||
ISOLATION RESISTANCE |
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25 / 70% RH |
|||
EMC EMISSION |
Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ( 50% load) ; EN61000-3-3 |
|||
EMC IMMUNITY |
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A |
|||
Others |
MTBF |
192.2K hrs min. MIL-HDBK-217F (25℃ ) |
||
DIMENSION |
228*68*38.8mm (L*W*H) |
|||
PACKING |
1.15Kg; 12pcs/14.8Kg/0.8CUFT |
|||
Note |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltages. Please check the static characteristics for more details. 5. Type A only. 6. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18. 7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 9. Refer to warranty statement. |
1. Todos os parâmetros NÃO especialmente mencionados são medidos na entrada 230VAC, carga nominal e 25 da temperatura ambiente. Nota
2. A ondulação e o ruído são medidos a 20MHz de largura de banda usando um cabo de par trançado de 12 "terminado com um capacitor paralelo 0.1uf & 47uf.
3. Tolerância: inclui tolerância de configuração, regulação de linha e regulação de carga.
4. A redução pode ser necessária sob baixas tensões de entrada. Por favor, verifique as características estáticas para mais detalhes.
5. Digite apenas um.
6. Segurança e design EMC referem-se a EN60598-1, CNS15233, GB7000.1, FCC part18.
7. O tempo de configuração é medido na primeira partida a frio. Ligar / desligar a fonte de alimentação pode levar a um aumento do tempo de configuração.
8. A fonte de alimentação é considerada como um componente que será operado em combinação com o equipamento final. Como o desempenho da EMC será afetado pela instalação completa, os fabricantes de equipamentos finais devem requalificar novamente a Diretiva EMC na instalação completa.
9. Consulte a declaração de garantia.Grupo de Produto : Acessórios LED > Fonte de alimentação à prova d'água Meanwell
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.